Clock / Stopwatch 1.8" 4D
Clock / Stopwatch 1.8" 4D - Image 2
Clock / Stopwatch 1.8" 4D - Image 3
Clock / Stopwatch 1.8" 4D - Image 4
Clock / Stopwatch 1.8" 4D - Image 5
Clock / Stopwatch 1.8" 4D - Image 6
Clock / Stopwatch 1.8" 4D - Image 7

Clock / Stopwatch 1.8″ 4D

$68.00

Description

This clock doubles as a stopwatch, countdown & count up timer and also a world clock.  There is a power-down memory, meaning that it will remember the last mode you are at. E.g. You selected countdown in HH:MM. When you power off and on, it remembers you are still in HH:MM mode so you can get it working immediately. There is also a built-in battery for the internal clock so time still continues even after power off. Built-in battery can last >5 years. This clock comes in many different colours you can select from.

You can turn the display on/off with the red power button. It also gives an output when the timer counts to 0.

There are 6 modes to choose from (press the respective remote button):

  • [0] for world clock
  • [1] for count up/down timer HH:MM
  • [2] for count up/down timer MM:SS
  • [3] for count up/down SS:MSMS
  • [7] for clock
  • [8] for date

World Clock Settings:

  • Press [0] to enter the world clock setting. You will see “—-” if the world clock is not set yet.
  • Press [EDIT] to enter edit mode. “—-” will start flashing.
  • Press [UP ARROW] to change to “Control” mode. You will see “Cont”. In control mode, the clock will act as master control and sync time with slave mode clocks. If you want to set the clock as master control, press [ENTER]. You will return to clock mode and the clock is set as the master control.
  • Press [UP ARROW] again to change to “Slave” mode. You will see “SLAV”. In slave mode, the clock will read data from the master control clock. If you want to set the clock as slave mode, press [ENTER]. You will see “H 00″. This is the offset hours from the main clock. Press [UP ARROW] and [DOWN ARROW] to select hour offset. A maximum of -12 to +12 hours can be set. Once done, press [ENTER]. You will see ”  00″. This is the offset minutes from the main clock. Press [UP ARROW] and [DOWN ARROW] to select minute offset. A maximum of -59 to +59 minutes can be set. Once done, press [ENTER]. You will return to clock mode and the clock is set as slave mode. If master control is not connected, you will see “0000”, if not you will see the respective offset time from the master control.
  • Press [SETUP] to start/stop seconds blinking.
  • There is no limit to how many slave clocks you can link together.

Count Up/Down Timer Settings:

  • Press [1] for HH:MM, [2] for MM:SS, [3] for SS:MSMS. Once done, you should see “00:00” if time is not set yet.
  • Press [EDIT] to enter edit mode. Digits will start flashing. Press the time you want to set accordingly. You can move between digits with the [LEFT ARROW] and [RIGHT ARROW].
  • Once done, press [ENTER] to save.
  • Press [UP ARROW] to begin count-up or [DOWN ARROW] to begin the countdown.
  • Once the timer reaches 0, the output will be triggered.
  • Press [DEL] to reset the clock to a previously set time.

Clock Settings:

  • Press [7] to enter clock mode.
  • Press [EDIT] to enter edit mode. Digits will start flashing. Press the time you want to set accordingly. You can move between digits with the [LEFT ARROW] and [RIGHT ARROW].
  • Once done, press [ENTER] to save.
  • Press [4] to switch between 12/24 hours format.
  • Press [SETUP] to start/stop seconds blinking.

Date Settings:

  • Press [8] to enter date mode.
  • Press [EDIT] to enter edit mode. Digits will start flashing. The date format is “DDMM”. Press the date you want to set accordingly. You can move between digits with the [LEFT ARROW] and [RIGHT ARROW].
  • Once done, press [ENTER] to save.

Switching Display for Time/Date Settings:

  • Press [9] to enter switching display mode. You will see “t 00” if the switching display is not set yet. Setting t to 0 will disable the switching display for time/date.
  • Press [EDIT] to enter edit mode. “00” will start flashing.
  • Setting t will determine how long the clock will be shown before switching to a date. Press [0-9] to set the time in seconds.
  • Once done, press [ENTER]. You will see “d 00” if the switching display is not set yet.
  • Setting d will determine how long date will be shown before switching to the clock. Press [0-9] to set the time in seconds.
  • Once done, press [ENTER]. You will return to clock mode and the clock will switch between clock and date based on the switching time.

Download Clock/ Stopwatch setup guide here

Technical Details

  • Input Voltage: 12V
  • Dimensions: 200 x 60 x 40mm
  • Weight: 500g

Shipping List

  • 1x Clock